"Waypoint has a leg turn back (teardrop turn) : ","0." "Hold Pattern position : -1=initialisation 0=first turn 1=opposite leg 2=turn back 3=come back init WPT : ","0." "Turn Direction 0=No current turn 1=Left 2=Right : ","0." "WPT STAR holding pattern completed : ","0." "Holding Pattern Armed or engaged : ","0." "Waypoint has an Holding pattern : ","0." "Approach Auto Barometric Altimeter","0." "Fuel On Board at Departure in Pounds","27437" "User descent Altitude Target value","3074." "Final Approach Altitude unlocked : ","0." "Speed first approach waypoint if Go Around : ","0." "Altitude first approach waypoint if Go Around : ","0." "Index first approach waypoint if Go Around : ","0." "Engine 2 Fuel burned since departure in Pounds : ","2061.5" "Engine 1 Fuel burned since departure in Pounds : ","2051." "SFCC Flaps config before takeoff : Aircraft is on ground : ","0." "User specific landing frequency : ","0." "Aircraft is above Mach Altitude MACH mode is engaged : ","1." "Inertial Data (0=Localization 1=Wind and speed): ","0." "Inertial Sys on/off (0=enabled 1=Disabled) : ","0." "FCU Settings : Knob FCU 0=selected mode 1=managed mode " "Climb Speed MACH Value above Conjunction Alt : ","1.","0.78" "QNH State : ","1."," 0=barometric value 1=STD" "Takeoff THUST mode 1=TOGA 2=FLEX : ","2." "Aircraft Descent phase","0."," 1=initial descent engaged 2=aicraft is above conjunction altitude 3=aircraft is between Conjunction altitude and 18000ft 4=aircraft is below 18000ft" "Aircraft Climb phase","3."," 0=aircraft is below 10000ft 1=Climb acceleration 2=Aircraft climb 3=Climb is completed 4=descent is engaged" "Takeoff phase","5."," -1=not cleared 0=Ready 1=takoff go 2=Aircraft is airborne 3=THR RED ALT reached 4=Initial acceleration 5=Aircrat is above 10000ft Takeoff is completed" "Aircraft takeoff state","1.","0=Takeoff is not completed:SFCC in Ground mode 1=had takeoff:SFCC in flight mode" "Flight Plan File","C:\\Documents and Settings\\Fdd\Mes documents\\Fichiers Flight Simulator X\\IFR Entzheim to Marseille Provence.PLN" You can open this file with a text editor or Excel, and post here the content. This file is saved in the Flight plan files folder (C:\Documents and Settings\Username\My documents\Flight Simulator X Files) depend of your Windows version.Įxemple : "IFR Entzheim to Marseille Provence.PLN FMS dataSave.csv" When a bug appears during a flight, Think to save you flight (names your savegame file ICAO to ICAO) When you save a flight, FD-FMC create a backup file of its data and flight setting in a CSV file called like the flight plan file with ".FMS dataSave.csv" at the end of the name. I never had this issue !! and nobody report to me this phenomenon !!! very strange !!! I was initially descending in managed mode but then I used manual V/S and that's when the zeroes were gone. Also, the V/S display is missing two zeroes, although when I took off all of them were present (as far as I remember) they disappeared during descent. After landing and vacating the runway on my first test flight, look at the MCP: the HDG numbers are missing. The320Pilot wrote:Francois, I think I had an issue with the A318.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |